Turned Oil Lamp

Updated on: Published on:
Turned segmented wood oil lamp with a lit wick beside two glasses of red wine on a wooden table

Seamless segmented turnings are a cinch, thanks to this 60° trick

Segmented turning work has more in common with quilting than most people might think. While quilters cut and sew scraps of fabric, I use a mitersaw to cut pieces of wood and join them with glue for similarly spectacular results. That said, I guess it’s not surprising that I look at quilts for inspiration. This pattern, called “a walk in the garden,” is easy to replicate and a perfect excuse to use up any special shorts in your lumber pile. The neat thing about this pattern is that it looks more difficult than it is. Once you know how to set your saw, you can assemble bunches of turning blanks, or use the segments to make a show-stopping cutting board.

Prep your parts

For a seamless top, mill your star and border strips (plus an extra for setup), and then set your mitersaw using the sequence shown at right. I used canary wood and paduak for the star and wenge for the border. The outer purpleheart band is the “star saver.” As you’ll see, it serves as a visual guide when shaping the lamp.

Using a Hitachi miter saw to cut a small piece of hardwood for a woodworking project
Set the saw to 30° and make the stop. Cut the end of your stop strip. The auxiliary fence and base reduce tearout and prevent parts from getting caught by the blade.
Hands adjusting a clamp and test strip on a miter saw fence for precise wood cutting.
Use a strip to set the stop. Position a test strip between the stop and saw blade, and then clamp the stop to the fence.

Hands assembling a wooden puzzle with various colored wood blocks on a workbench.Piece the puzzle together

Assembling the “walk in the garden” pattern can be a walk in the park with a few tips. First, do your assembly on a flat, nonstick surface. Next, use tape instead of clamps. I use masking tape to tack the parts and stretchable packing tape to pull the pattern together (see Buyer’s Guide, p. 61). When the glue dries, sand the pattern’s bottom face to remove excess glue, and fix any unevenness. If you don’t own a thickness sander, simply stick a sheet of sandpaper to a flat surface.

Hands applying wood glue to a segmented wooden puzzle with various wood species pieces.
Add the glue. After you’ve come up with a pleasing pattern, fold open each joint and apply glue.
Hands applying clear tape to a segmented wood turning blank with star pattern and purple clamps.
Wrap it tight. After gluing on the star-saver strips, wrap the assembly with stretchable tape. No additional clamps are needed.
Hands using a rubber mallet to assemble a colorful segmented wood inlay piece on a flat surface.

Tap it flat. Remove the masking tape, then fix any pieces that might have shifted.

Miter saw cutting a 60-degree angled step joint on two wood pieces clamped together.
Hands holding a small, multi-faceted turned wooden oil lamp base in a workshop setting
Woodworker using Quick-Grip clamps to glue colorful segmented wood pieces on round base
Exploded view of turned oil lamp showing segmented star top, veneer layer, and round wooden base with measurements.

Woodworker using drill press with depth gauge to bore a hole in turned wooden oil lamp baseTake it for a spin

As you can see, the finished lamp is a basic dome. I keep the shape simple because I don’t want to pull attention away from the top. A profile template really isn’t necessary; in fact, it may slow you down if your blanks vary in size.

The most important thing is not to turn too much, or else you might cut into your star. Pay attention to the “star keeper” strips. When those ends are flush with the outer lamp’s border, it’s time to move onto scraping, sanding, and finishing.

Hands adjusting a lathe chuck while holding a segmented wood blank for turning an oil lamp base
Hand using a gouge chisel to shape a wooden oil lamp on a lathe in a workshop
Hand using a gouge chisel to shape a spinning wooden blank on a lathe for a turned oil lamp.
Hand turning a wooden oil lamp base on a lathe with wood shavings flying

Hands using a power carving tool to shape a wooden piece mounted on a lathe in a workshop.Now finish it up

Because of the variety of species and changing grain direction, turning a segmented blank often means dealing with a little tearout and tool marks. A right-angle sander quickly makes things right. I start with 100 grit and work up to 400.

A common problem with exotic woods is keeping the colors from bleeding when applying a finish. To prevent this, I seal the piece, apply lacquer, and then use superfine abrasives to polish the finish. After giving it a quick coat of wax, it’s ready to light the night.

Hand spraying finish on a wooden bowl mounted on a lathe in a workshop.
Seal in the color. Fast-drying sanding sealer prevents the darker pieces from bleeding onto the lighter ones. Spray on 4 mist coats (wait a few minutes between coats) before scuff-sanding to remove nibs.
Hands sanding a rounded wooden oil lamp body on a lathe in a woodworking workshop
Spray it on, then buff it up. Spray lacquer dries quickly, but I give it a day to cure before polishing. For a soft sheen, press a white pad against the lamp and let the lathe do the work.
Woodworker applying finish to turned wooden oil lamp on lathe with cloth.

Polish and protect. With the lathe set to around 1000, squeeze a small dollop of sunscreen onto a paper towel, and apply to the lamp. Give it a few minutes to dry, then buff.

Back to blog Back to issue